₹ 530.00
Launch into the world of electronics with this All-in-One Starter Kit! Build circuits, experiment with lights and sounds, and explore electronic fundamentals – all from your workbench. This comprehensive kit includes everything you need to get started, from LEDs and resistors to transistors and voltage regulators. Perfect for beginners, hobbyists, and students!
SALE
-29%
₹ 250.00
- 1 x PIR Motion Sensor
- 1 x IR Sensor
- 1 x Soil Moisture Sensor
- 1 x LDR Sensor
- 1 x DHT11 Temperature & Humidity Sensor
- 1 x HC-SR04 Ultrasonic Sensor
₹ 949.00
- The best option to starting learn about IOT.
- High quality IOT Basic Learning kit with 100% compatible with NodeMCU.
- All components compatible with NodeMCU, can be used directly.
₹ 899.00
Expand your Arduino horizons with the Basic Starter Kit! This comprehensive kit builds upon the essentials and introduces a wider range of sensors, actuators, and control elements. Explore sound, movement, distance sensing, and more – all compatible with Arduino SMD UNO. Perfect for makers and hobbyists to take their projects to the next level!
₹ 40.00
Wire Length :- 20 CM
Kit Includes :-
- 10 Male-Male Jumper Wire
- 10 Male-Female Jumper Wire
- 10 Female-Female Jumper Wire
₹ 490.00
- Acrylic Transparent Chassis 2
- Coded Disk 4
- Acrylic Fasteners 8
- M3 Copper Stand-Off (Male-Female) 6
- M3 Cross-Head Bolt (Length: 8 mm ) 6
- M3 Cross-Head Bolt (Length: 30 mm ) 8
- M3 Nut 16
- Wheels 4
- BO Motors 4
₹ 105.00
- Male to Male, Male to Female, Female to Female Jumper Wires, 120 Pieces
- Each cable length about 20cm or 8-inch
- Good quality Product
₹ 205.00
- Operating Voltage (logic level): 5V
- With Soldered Connector
- 8 analog inputs ports: A0 ~ A7
- 14 Digital input / output ports: TX, RX, D2 ~ D13
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
₹ 240.00
- Microcontroller : ATmega328 SMD.
- Operating Voltage : 5V.
- Supply Voltage recommended : 7-12V DC.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
- DC Current per I/O Pin : 40 mA.
- DC Current for 3.3V Pin : 50 mA.
- Flash Memory : 32 KB (ATmega328) of which 0.5 KB used by bootloader.
- SRAM : 2 KB (ATmega328).
- EEPROM : 1 KB (ATmega328).
- Clock Speed : 16 MHz.
₹ 28.00
- USB Type: Type-A to Type-B
- Weight: 25 gm.
- Length: 20 cm.
- Fully compatible with the PC.
- Aluminum under-Mold shield helps meet FCC requirements on KMI/RFI interference.
₹ 150.00
- Blue Backlight with white words
- uses 4 Bit Arduino LCD Library
- Left, Right, Up, Down and Select buttons
- Screen contrast adjustment
- Arduino Reset button
- Operating Voltage is 5V
₹ 240.00
- Circuit Operating Voltage: 5V
- Clock frequency: 16MHz.
- Digital I/O Pins: 14
- 8 analog input port: A0 ~ A7.
- A pair of TTL level serial port transceiver : RX / TX.
- 6 PWM port: D3, D5, D6, D9, D10, D11.
- Use For Atmel Atmega328P-AU microcontroller.
- Support serial download.
- Support 9V battery.
- Package Includes :
- 1 x Pro mini 5v/16mHZ compatible
₹ 411.00
| Model Type | Arduino Leonardo |
| Microcontroller Chip | ATmega32u4 |
| Operating Voltage | 5 |
| Input Voltage(Recommended) | 7V-12V |
| Input Voltage (limit) | 6V-20V |
| Analog I/O Pins | 12 |
| Digital I/O Pins | 20 |
| PWM Digital I/O Pins | 7 |
| DC Current per I/O Pin | 40 mA |
| DC Current for 3.3V Pin | 50 mA |
| Clock Speed | 16 MHz |
| Flash Memory | 32 KB (ATmega32u4) of which 4 KB used by bootloader |
| SRAM | 2.5 KB |
| EEPROM | 1 KB |
| Dimensions in mm (LxWxH) | 68x54x20 |
| Weight (gm) | 20 |
₹ 110.00
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection
- diodes. Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- Pull-down resistors keep motors disabled during power-up
- Big terminal block connectors to easily hook up wires (18-26AWG) and power
- Arduino reset button brought up top
- 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
- Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
₹ 255.00
Package Includes :
1 x JoyStick Shield Module Robotics Control.
Additional information
| Input Supply voltage (V) | 3.3 ~ 5 |
| Color | Red |
| Length (mm) | 87 |
| Width (mm) | 53 |
| Height (mm) | 30 |
| Weight (gm) | 37 |
₹ 95.00
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Coolant enable
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
₹ 0.40
SPECIFICATION
| Package | SOD−80 |
| Diode Type | SMD |
| DC Forward Current | 300 mA |
| Maximum Repetitive Reverse Voltage | 100 V |
| Power Dissipation | 500 mW |
| Total Capacitance | 2.0 pF |
₹ 0.50
| Symbol | Parameter | Value | Units |
| VRRM | Peak Repetitive Reverse Voltage | 1000 | V |
| IF(AV) | Average Rectified Forward Current | 1 | A |
| I2t | Rating for fusing | 30 | A |
| IFSM | Non- Repetitive Peak Forward Surge Current | 3.7 | A2sec |
| TJ | Operating Junction Temperature | 55 to +175 | ℃ |
| Tstg | Storage Temperature Range | 55 to +175 | ℃ |
₹ 7.00
| Rated Voltage | 125V |
| Rated Current | 6A |
| Switch Type | SPDT |
| Function | ON-OFF-ON |
| Number of Pins | 3 |
| Mounting Type | Panel Mount |
| Size | 33x13x8mm |
₹ 0.90
| Transistor Polarity | NPN |
| Collector-Base Voltage (VCBO) | 50VDC |
| Collector-Emitter Voltage (VCEO) | 45VDC |
| Emitter-Base Voltage (VEBO) | 6VDC |
| Continuous Collector Current (IC) | 100mA |
| Output Capacitance (Cobo) | 4.5pF |
| Transition Frequency (fT) | 300MHz |
| DC Current Gain (hFE) | 110-800 |
| Operating Temperature Range | -55 – 150°C |
| Power Dissipation (PD) | 625mW |
₹ 0.80
| Capacitance | 100nF |
| Tolerance(%) | 10 |
| Voltage (V) | 50 |
| Dissipation factor (D.F.) | ±2.5% |
| Operating Temperature Range (°C) | -55 to 125 |
| Mounting Type | SMD |
₹ 1.30
- Product: BC557 Transistor
- Polarity: PNP
- Number of pins: 3
- package: TO-92
- Mounting type: Through hole
- Package contains: 5 x BC557 General Purpose PNP Amplifier
₹ 0.70
| Package | 1206 |
| Colour | Blue |
| Forward voltage | 2.2 – 3 volts |
| Peak Reverse Voltage | 5 volts |
| Max DC Forward Current | 25 mA |
| Reverse Current | 10 uA |
| Max Power Dissipation | 60 mW |
| Lens Color | Diffused white |
| Typical Luminous Intensity | 8 MCD |
| Typical Viewing Angle | 120 deg |
₹ 0.70
| Package | 1206 |
| Colour | Green |
| Forward voltage | 2.2 – 3 volts |
| Peak Reverse Voltage | 5 volts |
| Max DC Forward Current | 25 mA |
| Reverse Current | 10 uA |
| Max Power Dissipation | 60 mW |
| Lens Color | Diffused white |
| Typical Luminous Intensity | 8 MCD |
| Typical Viewing Angle | 120 deg |
₹ 2.15
- 16 pins.
- JDEC compliant.
- Molded notch for proper orientation.
- Easy to insert and remove ICs.
₹ 6.00
| Material | High-Quality Plastic |
| Fuse Dimension | 5mmx20mm |
| Colour | Black |
| Temperature Range | -20°C to 85°C |
₹ 8.00
- Contactless transmission of data and supply energy (no battery needed)
- Operating distance: Up to 100mm (depending on antenna geometry)
- Operating frequency: 13.56MHz
- Data transfer: 106 kbit/s
- Data integrity: 16 Bit CRC, parity, bit coding bit counting
- Anticollision
- Typical ticketing transaction: <100 ms ( including backup management)
₹ 32.00
- 1 channel relay board
- Operating Voltage 5V
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC5V: 10A
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for avoidance of malfunction
- Power supply indicator lamp
- Control indicator lamp
- Indicator for Relay output status
- Can Be controlled various appliances & other Equipment With Large current.
- Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
- The module is compliant with international safety standards, control and load areas isolation trenches;
₹ 80.00
- Operating Current :13-26mA / DC 3.3V
- Idle Current :10-13mA / DC 3.3V
- Sleep Current: < 80uA
- Peak Current: < 30mA
- Operating Frequency: 13.56MHz
- Supported card types: mifare1 S50, mifare1 S70 MIFARE Ultralight, mifare Pro, MIFARE DESFire
- Environmental Operating Temperature: -20 – 80 degrees Celsius
- Environmental Storage Temperature: -40 – 85 degrees Celsius
- Relative humidity: relative humidity 5% – 95%
- Reader Distance: ≥ 50mm / 1.95″ (mifare 1)
- Module Size: 40mm × 60mm
- Module interface: SPI
- Data transfer rate: Maximum 10Mbit/s
₹ 480.00
- Model: TPA3116D2 (2x80W)
- Chip Protection: Overvoltage, Under-voltage, Superheat, DC detection, Short circuit
- Supply Voltage: DC 12V to 24V
- Output Power: 80W x 2
- Power Efficiency: > 90%
- Dimensions: Length 32mm, Width 60mm, Height 14mm
- Weight: 45 grams
₹ 199.00
- Operating Voltage: The module can operate within a wide voltage range, from DC 8V to 24V. This flexibility allows it to be powered by various sources, making it versatile for different setups.
- Chipset: It utilizes the TPA3118 chipset, a reputable choice for achieving high-quality audio amplification.
- Material: The board is constructed from FR4 material, known for its durability and reliability.
- Dimensions: The module’s compact size ensures it can fit into tight spaces. It measures 47mm in length, 35.5mm in width, and 12mm in height.
- Weight: The module is lightweight, weighing only 12 grams, which is advantageous for portable and space-constrained applications.
₹ 42.00
| Voltage(V) | DC 35V |
| Operating Current (A) | 0.1 |
| Contact Resistance | 500 |
| Insulation Resistance (M) | 100 |
| Dielectric Strength | 250VRms |
| Length (mm) | 165 |
| Width (mm) | 70 |
| Height (mm) | 1 |
| Weight (gm) | 7 |
₹ 205.00
- Profiles: Bluetooth serial port Profile
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Frequency: 2.4GHz ISM band
- Modulation: GFSK(Gaussian Frequency Shift Keying)
- Emission power: ≤4dBm, Class 2
- Sensitivity: ≤-84dBm at 0.1% BER
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps
- Security: Authentication and encryption
- Power supply: +3.3VDC 50mA
- Working temperature: -20 ~ +75Centigrade
- Dimension: 26.9mm x 13mm x 2.2 mm
₹ 5.00
| Parameter | Value |
| Supply Voltage | 32V |
| Differential Input Voltage | 32V |
| Input Voltage | −0.3V to +32V |
| Operating Temperature Range | −25˚C to +85˚C |
| Storage Temperature Range | −65˚C to +150˚C |
| Lead Temperature DIP | 260˚C |
₹ 5.00
| Symbol | Parameter | Rating | Unit |
| VCC | Supply voltage | 18 | V |
| VI | Input voltage | VCC | V |
| IO | Output current | ±225 | mA |
| Θja | Package thermal resistance Junction-to-Ambient | 130 | °C/W |
| θJC | Package thermal resistance Junction-to-Case | 15 | °C/W |
| TJ | Junction temperature | 150 | °C |
| TSTG | Storage temperature | -65 to 150 | °C |
₹ 20.00
| Symbol | Parameter | Min | Type | Max | Unit |
| VCC | Supply Voltage | 4.75 | 5 | 5.25 | V |
| TA | Operation free-air temperature | 0 | 25 | 70 | °C |
| IOH | Output Current — High | -0.4 | mA | ||
| IOL | Output Current — Low | 8 | mA |
₹ 12.00
- Output Type: Fixed
- Output Voltage: +18V DC
- Current Output: up to 1.5A
- Input Voltage: 21 – 35VDC
- Quiescent (standby) current: 8mA
- Dropout Voltage (Max): 2 V @ 1A
₹ 78.00
- High Performance, Low Power AVR 8-Bit Microcontroller
- Advanced RISC Architecture
- 120 Powerful Instructions
- Operating Voltage : 1.8 – 5.5V
- 32 x 8 General Purpose Working Registers
₹ 1.80
- Model: 18650 radiating battery spacer.
- Material: ABS/PC (Remarkable Flame Retardant Plastic).
- Bore Diameter: 18.5mm
- Combined them into many different sizes and shapes of the battery pack.
- Application: Design for Radiating Complex Battery Packs. Safe and Stable, Perfect Build for eBike!
₹ 100.00
- Input Voltage: 230V AC
- Output Voltage: 12V, 12V or 0V
- Output Current: 2 Amp
- Mounting: Vertical mount type
- Winding: Copper
₹ 1,050.00
- Input Voltage: AC 100 – 264V 50 / 60Hz
- Output Voltage: 12V DC, 10A
- Output voltage: Adjustment Range: ±20%
- Protections: Overload / Over Voltage / Short Circuit
SALE
-7%
Original price was: ₹ 280.00.₹ 260.00Current price is: ₹ 260.00.
₹ 180.00
- Input Voltage: 230V AC
- Output Voltage: 12V, 12V or 0V
- Output Current: 3 Amp
- Mounting: Vertical mount type
- Winding: Copper
SALE
-7%
Original price was: ₹ 300.00.₹ 280.00Current price is: ₹ 280.00.
₹ 700.00
- Input Voltage: AC 100 – 264V 50 / 60Hz
- Output Voltage: 12V DC, 10A
- Output voltage: Adjustment Range: ±20%
- Protections: Overload / Over Voltage / Short Circuit
₹ 5.00
- Operating Temperature Range : (deg. C)-20 to +85
- This CR2032 Battery provides an excellent combination of high energy and continuous voltage supply
- These batteries provide long shelf life for back up energy purposes together with ideal temperature resistance and superior storage capacity
- Voltage:3V, Chemistry: Lithium, Model : CR2032, 5 Pc Cell Weight : 20 g
₹ 4.50
| Cell Size: | Coin-Cell |
| Number of Cells: | 1 |
| Connector Type: | PC Mount |
| Product Type: | Battery Holder (open) |
| Dimension (LxWxH): | 28x31x12 mm |
| Voltage Rating: | 3V / 210 mAh |
₹ 150.00
- Input Voltage: 230V AC
- Output Voltage: 9V, 9V or 0V
- Output Current: 1 Amp
- Mounting: Vertical mount type
₹ 30.00
- Model: MC38
- Material: Plastic
- Color: White
- Voltage: 100V
- Contact Capacity: (Max. Switch Current) 0.5A
- Rated Power: 10W
- Actuation Distance: 15 ~ 25mm
- Connecting cable length: 30cm
₹ 82.00
- Power Supply: 5 Volts
- Interface Type: Analog & Digital
- High Sensitivity to Smoke & combustible gasses like Hydrogen, LPG & Propane.
- Low Cost.
- Stable & Long Life.
- On board Power indication.
₹ 25.00
- Input Voltage: DC 3.3V to 5V
- Output: Analog and Digital
- Sensitivity adjustable
₹ 54.00
- Working Voltage:5V (DC)
- Static Current: Less than 2mA
- Output Signal:5V
- Sensor Angle: Less than 15 Degrees
- Detection Distance: 2 cm to 450 cm
- High Precision: Up to 2 mm
- Input Trigger Signal: 10µs TTL impulse
- Echo Signal: Output TTL PWL Signal
- High sensitivity ultrasonic range sensor
- Works with Arduino board
₹ 55.00
- Color: White + Green OR White + Blue
- Infrared Sensor with Control Circuit Board
- The Sensitivity and Holding Time Can be Adjusted
- Working Voltage Range: DC 4.5V- 20V
- Current Drain: <60uA
- Detection Range: <140°
- Voltage Output: High/Low level Signal: 3.3V TTL output
- Detection Distance: 3 to 7m (can be adjusted)
- Delay Time: 5 to 200s (Can be Adjusted, Default 5s +/- 3%)
- Blockade time: 2.5s (Default)
- Work temperature: -20-+80°C
- Dimension: 3.2cm x 2.4cm x 1.8cm (Approx)
- Sensitive Setting: Turn to Right, Distance Increases (About 7M); Turn to Left, Distance Reduce (About 3M)
- Time Setting: Turn to Right, Time Increases (About 200S); Turn to Left, Time Reduce (About 5S).
