Subcategories:
₹ 150.00
- Blue Backlight with white words
- uses 4 Bit Arduino LCD Library
- Left, Right, Up, Down and Select buttons
- Screen contrast adjustment
- Arduino Reset button
- Operating Voltage is 5V
₹ 411.00
| Model Type | Arduino Leonardo |
| Microcontroller Chip | ATmega32u4 |
| Operating Voltage | 5 |
| Input Voltage(Recommended) | 7V-12V |
| Input Voltage (limit) | 6V-20V |
| Analog I/O Pins | 12 |
| Digital I/O Pins | 20 |
| PWM Digital I/O Pins | 7 |
| DC Current per I/O Pin | 40 mA |
| DC Current for 3.3V Pin | 50 mA |
| Clock Speed | 16 MHz |
| Flash Memory | 32 KB (ATmega32u4) of which 4 KB used by bootloader |
| SRAM | 2.5 KB |
| EEPROM | 1 KB |
| Dimensions in mm (LxWxH) | 68x54x20 |
| Weight (gm) | 20 |
₹ 205.00
- Operating Voltage (logic level): 5V
- With Soldered Connector
- 8 analog inputs ports: A0 ~ A7
- 14 Digital input / output ports: TX, RX, D2 ~ D13
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
₹ 240.00
- Circuit Operating Voltage: 5V
- Clock frequency: 16MHz.
- Digital I/O Pins: 14
- 8 analog input port: A0 ~ A7.
- A pair of TTL level serial port transceiver : RX / TX.
- 6 PWM port: D3, D5, D6, D9, D10, D11.
- Use For Atmel Atmega328P-AU microcontroller.
- Support serial download.
- Support 9V battery.
- Package Includes :
- 1 x Pro mini 5v/16mHZ compatible
₹ 240.00
- Microcontroller : ATmega328 SMD.
- Operating Voltage : 5V.
- Supply Voltage recommended : 7-12V DC.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
- DC Current per I/O Pin : 40 mA.
- DC Current for 3.3V Pin : 50 mA.
- Flash Memory : 32 KB (ATmega328) of which 0.5 KB used by bootloader.
- SRAM : 2 KB (ATmega328).
- EEPROM : 1 KB (ATmega328).
- Clock Speed : 16 MHz.
₹ 28.00
- USB Type: Type-A to Type-B
- Weight: 25 gm.
- Length: 20 cm.
- Fully compatible with the PC.
- Aluminum under-Mold shield helps meet FCC requirements on KMI/RFI interference.
₹ 95.00
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Coolant enable
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
₹ 255.00
Package Includes :
1 x JoyStick Shield Module Robotics Control.
Additional information
| Input Supply voltage (V) | 3.3 ~ 5 |
| Color | Red |
| Length (mm) | 87 |
| Width (mm) | 53 |
| Height (mm) | 30 |
| Weight (gm) | 37 |
₹ 110.00
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection
- diodes. Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- Pull-down resistors keep motors disabled during power-up
- Big terminal block connectors to easily hook up wires (18-26AWG) and power
- Arduino reset button brought up top
- 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
- Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO