Subcategories:
₹ 30.00
| Trigger Voltage (VDC) | 12 |
| Trigger Current (mA) | 20 |
| Switching Voltage (VAC) | 250@10A |
| Switching Voltage (VDC) | 30@10A |
| Operating Temperature (C) | -40 to 85 |
| Opt. Relative Humidity(RH) | 20% 85% |
| Storage condition () | 65 to 125 |
| Length (mm) | 48 |
| Width (mm) | 29 |
| Height (mm) | 17 |
| Weight (gm) | 15 |
₹ 32.00
- 1 channel relay board
- Operating Voltage 5V
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC5V: 10A
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for avoidance of malfunction
- Power supply indicator lamp
- Control indicator lamp
- Indicator for Relay output status
- Can Be controlled various appliances & other Equipment With Large current.
- Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
- The module is compliant with international safety standards, control and load areas isolation trenches;
SALE
-14%
Original price was: ₹ 70.00.₹ 60.00Current price is: ₹ 60.00.
- High current relay, AC250V 10A, DC5V 10A
- 2 LEDs to indicate when relays are on
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
₹ 120.00
| Channel | 4 |
| Trigger Voltage (VDC) | 12 |
| Trigger Current (mA) | 20 |
| Switching Voltage (VAC) | 250@10A |
| Switching Voltage (VDC) | 30@10A |
| Mounting hole dimensions | Diameter=3mm, X-axis pitch=68mm Y-axis pitch=48mm |
| Length (mm) | 75.5 |
| Width (mm) | 55.5 |
| Height (mm) | 20 |
| Weight (gm) | 58 |
₹ 42.00
- Length of cable + connector: 93mm
- 7-pin 0.1″ pitch connector
- Weight: 7.5 grams
- Keypad dimensions: 68.5mm x 76.5mm x 1mm
₹ 42.00
| Voltage(V) | DC 35V |
| Operating Current (A) | 0.1 |
| Contact Resistance | 500 |
| Insulation Resistance (M) | 100 |
| Dielectric Strength | 250VRms |
| Length (mm) | 165 |
| Width (mm) | 70 |
| Height (mm) | 1 |
| Weight (gm) | 7 |
₹ 100.00
- Range in open space(Standard Conditions) : 100 Meters
- RX Receiver Frequency : 433 MHz
- RX Typical Sensitivity : 105 Dbm
- RX Supply Current : 3.5 mA
- RX IF Frequency : 1MHz
- RX Operating Voltage : 5V
- TX Frequency Range : 433.92 MHz
- TX Supply Voltage : 3V ~ 6V
- TX Out Put Power : 4 ~ 12 Dbm
₹ 200.00
| Operating Voltage (VDC) | 6V ~ 30 |
| Supply Current (A) | 0.05 |
| Trigger Voltage (VDC) | 5 |
| Switching Voltage (VAC) | 250@10A |
| Switching Voltage (VDC) | 30@10A |
| Operating Temperature (C) | -40 to 85 |
| Storage condition () | -40 to 80 |
| Length (mm) | 63 |
| Width (mm) | 38 |
| Height (mm) | 18 |
| Weight (gm) | 26 |
₹ 65.00
- Voltage: 5 Volts
- It’s for 8 Pin NRF24L01+ Module
- A simple socket board which is for NRF24L01 wireless module
- On-board AMS1117-3.3 chip
- It can be used with NRF24L01 wireless module
- On-board 3.3 Volt voltage regulator accepts your Arduino +5 Volt supply and provides 3.3 Volts for the attached nRF24L01+ module
- Small power on SMD LED indicator
- On-Board Voltage Regulator:
– Voltage Regulator Input Voltage (connected to VCC): 4.8 Volt to 12 Volt
– Voltage Regulator Input Voltage Max: 15 Volts (we recommend staying below 12V)
₹ 125.00
| Operating Voltage(VDC) | 12 |
| Supported File Format | fat 32, fat 16 file system |
| Signal to Noise Ratio | 65db |
| Separation | 45 db |
| Auto-Search Station | 22-28 db |
| The frequency range for FM | 87.5-108 MHz |
| Distortion | 0.2% |
| Output | 550 mv |
| Dimensions in mm (LxWxH) | 107 x 27 x 30 |
| Distance Between Mounting Hole | 96 mm |
| Weight (gm) | 20 |